How to Change the sunstate Kirby Bag:

Changing the bag on your sunstate Kirby vacuum cleaner is straightforward. Here’s how to do it:

1. Begin by unzipping the outer bag and pulling out the top adaptor.
2. Remove a new disposable bag from its packaging.
3. Position the cardboard faceplate of the disposable filter bag against the bottom of the adaptor.
4. Pivot the faceplate against the adaptor’s flat surface. Then, bend and press the tab at the top of the faceplate until it clicks into place and is secure.
5. Attach the bag support strap through the small hole on the adaptor, ensuring it goes over the stud for a firm connection.
6. Place the entire assembly inside the outer bag.
7. Finally, close the zipper to secure the bag.

By following these steps, your sunstate Kirby vacuum will be ready for use with a fresh bag, ensuring optimal cleaning performance.

How to install the Power Nozzle:

Installing the Power Nozzle on your vacuum is an easy process. Follow these steps:

1. Start by pulling the belt lifter handle, located on the Power Nozzle or the vacuum head, toward you. Then, turn it counterclockwise until the red arrows align. This action should catch and stretch the belt inside the nozzle.
2. Next, lift the headlight hood of the vacuum.
3. Attach the two hooks found on the back of the nozzle onto the attaching bar, which you can find on the front of the unit.
4. Press the nozzle firmly against the unit and secure it in place using the Accessory Lock.
5. Finally, pull the belt lifter handle toward you again and turn it clockwise until the green arrows are aligned. For more detailed instructions, refer to page 22 of the owner’s manual.

By following these steps, you’ll successfully install the Power Nozzle, readying your vacuum for efficient cleaning.

How to adjust the Power Nozzle height:

Adjusting the height of your vacuum’s Power Nozzle is simple with the toe-touch control, conveniently located above the front wheel. The control features numbered settings for carpet and floor adjustments and dotted settings for accessories and various cleaning requirements. Follow these steps to adjust the Power Nozzle height:

1. Turn the vacuum unit on.
2. Press the toe-touch upper control pedal repeatedly until the Power Nozzle is at its lowest setting.
3. To raise the Power Nozzle to your desired height, press the toe-touch lower control pedal incrementally, one notch at a time. You should hear a click each time it adjusts up or down.

This method allows for precise height adjustment to suit different carpet heights and cleaning needs, ensuring optimal cleaning performance.

Installing the Hose :

Installing the hose on your vacuum unit is straightforward. Please ensure safety first by following these steps:

1. Turn off the unit and unplug it from the electrical outlet.
2. Remove the Power Nozzle (refer to page 22 of the owner’s manual for detailed instructions).
3. Clean the motor shaft by wiping it down.
4. Position the hooks of the attachment hose over the attaching bar located on the unit.
5. Push the hose firmly against the unit and turn the accessory lock clockwise to secure it in place.
6. Lower the headlight hood.
7. Plug in the unit, turn it on, and it’s ready for use with the hose attached.

These steps will ensure your hose is properly installed for effective use.

Installing the Handheld for Portable Cleaning

Transforming your upright vacuum into a portable cleaner enhances its versatility, allowing you to easily clean stairs or bed mattresses. Follow these steps for a smooth conversion:

1. Ensure the vacuum unit is turned off and unplugged from the power source.
2. Set the Tech Drive Power Assist to neutral.
3. Release the outer bag by pressing the Bag Release Button.
4. Detach the power cord from the handle.
5. Press the handle release button located at the bottom of the unit, then pull the upright handle straight up and out of its slot.
6. With the upright handle removed, insert the portable handle into the slot previously occupied by the upright handle.
7. Fold the outer bag in half and insert the bag latch tab into the slot on the portable handle, ensuring the zipper is facing upwards.

By following these steps, you’ll successfully convert your vacuum into a handheld version, ready for detailed cleaning tasks.

How to Use the Tech Drive (Drive Mode)

The Tech Drive Power Assist feature is designed to facilitate the maneuvering of your vacuum while it’s in use. To engage the Tech Drive in Drive Mode, simply press down on the pedal marked “D” for drive. This activates the power assist, significantly reducing the effort required to push and pull the vacuum during operation. It’s especially helpful while you’re vacuuming, shampooing carpets, or scrubbing hard floors, making the process smoother and more efficient.

How to Use the Tech Drive (Neutral Mode)

Switching the Tech Drive to Neutral Mode is done by pressing down on the pedal marked “N”. In this mode, the unit becomes much easier to move when it’s turned off, allowing for effortless repositioning or transportation of the vacuum. Neutral Mode is ideal for:

• Moving the Kirby system without engaging the motor, such as when transitioning between cleaning areas or navigating through your home.
• Vacuuming hard floors where you might prefer a lighter touch.
• Polishing hardwood floors with products like the Miracle Shine High Gloss Floor Finish, where controlled, manual movement may be preferred for even application.

By understanding and utilizing the Tech Drive’s Drive and Neutral modes, you can optimize your Kirby system’s performance for a variety of cleaning tasks, ensuring efficient and effective use across different surfaces and conditions.

How to Change a Belt on Your Vacuum Cleaner

Changing the belt on your vacuum cleaner’s Power Nozzle is a straightforward process. Follow these steps to ensure a proper belt replacement:

1. Begin by turning the nozzle belt lifter on your Power Nozzle clockwise until the green arrows align.
2. Flip the Power Nozzle over and gently pull up on the belt to loosen and remove the brush roll that is currently in place.
3. Slide off the old belt from the brush roll and replace it with a new belt.
4. Reinsert the brush roll back into the Power Nozzle.
5. While holding the belt up with one finger, use the handle on the belt lifter to turn it counterclockwise until the red arrows align. This will engage the belt lifter hook to catch and stretch the belt.
6. Reattach the Power Nozzle to your Kirby system. Finally, rotate the belt lifter until the green arrows line up once more, indicating that the belt is correctly installed and tensioned.

By following these instructions, you can easily change the belt and maintain the optimal performance of your vacuum cleaner.

How to Install the Multi-Surface Shampoo System (MSSS):

To utilize the MSSS for shampooing carpets and cleaning hard surface floors, follow these steps:

1. Start by removing the Power Nozzle from your vacuum.
2. Next, detach the outer bag.
3. Lift and remove the waste tray from the MSSS and set it aside temporarily.
4. When shampooing carpets, ensure the carpet brush roll is installed. If necessary, insert the baffle strip with the flat side facing towards the brush roll.
5. Press the toe-touch control bottom pedal all the way down to elevate the front of the unit.
6. With the front raised, connect the hooks located on the rear of the MSSS to the attaching bar on the unit.
7. Push the MSSS firmly against the unit and turn the Accessory Lock clockwise to secure it in place.
8. Rotate the nozzle belt lifter clockwise until the green arrows align, then lower the headlight hood.
9. Finally, reinsert the waste tray into the MSSS.

Following these instructions will ensure your MSSS is correctly installed and ready for carpet shampooing or hard surface floor cleaning.

Install the Hard Floor Brush Roll:

To prepare your machine for cleaning hard surface floors, follow these steps:

1. Start by removing the power nozzle (the head of the machine) and the outer bag.
2. Next, remove the Waste Tray from the Multi-Surface Shampoo System (MSSS).
3. To remove the carpet brush roll and install the Rotary Mop, turn the MSSS nozzle belt handle clockwise until the green arrows align.
4. Flip the nozzle upside down and pull on the belt to loosen it, then remove the carpet brush roll.
5. Detach the belt from the carpet brush roll and attach it to the Rotary Mop.
6. Once the belt is secured on the Rotary Mop, reinsert it into the MSSS.
7. Push up on the belt with your finger and turn the belt lifter handle counterclockwise until the red arrows align.
8. Press the toe-touch pedal all the way down to raise the front of the unit.
9. Attach the hooks on the back of the MSSS to the attaching bar on the unit.
10. Push the MSSS against the unit, lock it in place by turning the Accessory Lock clockwise, and then turn the belt lifter clockwise until the green arrows align.
11. Lower the headlight hood and reinstall the waste tray.

These steps will ensure your machine is correctly converted and ready for cleaning hard surface floors.

Install the Tile & Grout Brush Roll:

To convert your machine for cleaning tile and grout, please follow these instructions:

1. Begin by removing the power nozzle (the head of the machine) and the outer bag. For detailed instructions, refer to page 22 of the owner’s manual.
2. Remove the Waste Tray from the Multi-Surface Shampoo System (MSSS).
3. Insert the Tile & Grout Brush Roll into the MSSS. Make sure the belt is properly placed on the brush roll.
4. With the belt on the brush roll, reinsert it into the MSSS.
5. Push up on the belt with your finger and turn the belt lifter handle counterclockwise until the red arrows align.
6. Press the toe-touch pedal all the way down to raise the front of the unit.
7. Attach the hooks on the back of the MSSS to the attaching bar on the unit.
8. Push the MSSS against the unit and secure it by turning the Accessory Lock clockwise. Then, turn the belt lifter clockwise until the green arrows align.
9. Lower the hood and reinstall the waste tray.

Following these steps will ensure your machine is properly set up for effective tile and grout cleaning.

Convert to Air Pump (Inflater):

1. Begin by removing the power nozzle, or front head of the vacuum. For guidance, refer to page 22 of the owner’s manual.
2. Attach the air guard by placing its hooks over the attaching bar located at the front of the unit. Secure it by pushing the air guard against the unit and turning the accessory lock clockwise.
3. Press the bag release button on the top of the outer bag and rotate the base of the bag away from the unit to remove it.
4. Finally, connect the hose to the air exhaust port. Align the arrow on the hose with the arrow on the port and twist the hose clockwise until it locks into place.

Convert to Air Pump (Deflater):

The process for converting your vacuum to function as a deflater is the same as converting it to an inflator. Simply follow the instructions above to attach the hose to the exhaust port, allowing you to use your vacuum as a blower for deflating items.

By following these steps, you can easily switch your vacuum’s functionality to meet your inflating or deflating needs.

Installing the Portable Sprayer:

To install the portable sprayer, first ensure your vacuum unit is set to blower mode. For detailed instructions on switching to blower mode, refer to page 26 of your owner’s manual. Once in blower mode, follow these steps to set up your sprayer:

1. Unscrew the jar from the sprayer and fill it three-quarters full with a non-flammable liquid.
2. Attach the dip tube to the sprayer before screwing the jar back in place.
3. Attach the sprayer to the end of the blower hose.
4. Hold the sprayer horizontally and turn the vacuum unit on.
5. Squeeze the trigger on the sprayer to release the solution onto a newspaper, ensuring it operates correctly.
6. Adjust the control on the trigger to modify the spray pattern as needed.

By following these steps, you can effectively install and use the portable sprayer with your vacuum in blower mode for various spraying tasks.

Installing the Portable Sprayer for Blower Mode

To use the portable sprayer, your vacuum must first be converted to blower mode. For detailed instructions on setting up blower mode, please refer to page 26 of your owner’s manual. Follow these steps to install the portable sprayer:

1. Attach the air guard to the unit by placing its hooks over the attaching bar located at the front of the unit. Secure it by pushing the air guard against the unit and turning the accessory lock clockwise.
2. Remove the outer bag by pressing the bag release button on the top of the bag and rotating the bottom base of the bag away from the unit.
3. Connect the hose to the air exhaust port. Align the arrow on the end of the hose with the arrow on the port and twist the hose clockwise until it locks.
4. With the unit in blower mode and the hose attached, prepare the sprayer by unscrewing the jar and filling it three-quarters full with a non-flammable liquid.
5. Attach the dip tube to the sprayer before screwing the jar back on.
6. Attach the sprayer to the end of the hose.
7. Hold the sprayer horizontally, turn the unit on, and squeeze the trigger to spray the solution onto a newspaper, verifying it functions properly.
8. Adjust the spray pattern by turning the control on the trigger as needed.

This setup allows you to use your vacuum in blower mode with the portable sprayer for various spraying tasks.

Installing the Turbo Accessory:

The Turbo Accessory is a versatile tool that can be used for sanding, polishing, or scrubbing tasks with your vacuum unit. To install and use the Turbo Accessory, follow these steps:

1. Start by assembling the turbo sander. Unsnap and lift off the sander dust shroud.
2. Rotate the clamp levers upward on the sides of the turbo accessory.
3. Slide a sheet of sandpaper into the front clamp and lock the lever securely.
4. Wrap the sandpaper tightly around the bottom of the turbo accessory and tuck the end into the rear clamp. Secure it by locking the clamp.
5. On a level surface, reattach the sander dust shroud, ensuring the opening is facing the back.
6. Insert the hose into the designated port on the turbo accessory.
7. Hold the turbo accessory securely at the top and bottom.
8. Turn your Kirby vacuum on, followed by turning on the turbo accessory.

By following these instructions, you’ll have successfully installed the Turbo Accessory, ready for your sanding, polishing, or scrubbing projects.